Clarion UNGO MS5500 Manuel d'utilisateur

installation_MS5500.qxd 12/6/99 11:59 AM Page 1

Page 6 - MS5500 Installation ManualLogicSensor IIOverrideSwitchStatusLEDWiring Diagraminstallation_MS5500.qxd 12/6/99 11:59 AM Page 6

MS5500 Installation Manual - Page 714-Pin Main HarnessPin 1 - BLACK: Ground.Connect to a solid chassis ground. Be sure to use a ring connector

Page 8 - MS5500 Installation ManualPin 11 - BLUE: Starter Defeat Normally Closed (-) outputProvides a negative output while the alarm is Armed and

MS5500 Installation Manual - Page 9Pin 14 - YELLOW/white: Auxiliary Function 1 negative outputProvides negative (-) output. Output will stay on

Page 10 - MS5500 Installation ManualJumper SelectionsParking Light Polarity. Selects the polarity (+/-) for the output of the on-board Parking Lightr

MS5500 Installation Manual - Page 11Accessing the Jumpers Using a flathead screwdriver, carefully press in on theaccess tabs on the sides of the ca

Page 12 - MS5500 Installation ManualRemote Transmitter LayoutEach system comes with 2 Remote Transmitters, pre-programmed to operate in the UngoStand

MS5500 Installation Manual - Page 13The Mode Button will change the function of Buttons 1 and 2 each time it is pressed, allowingButtons 1 and 2 to

Page 14 - MS5500 Installation ManualButton 1 Arms the system. This Button also locks the doors when the system is in Valet Mode.Button 2 Disarms the

MS5500 Installation Manual - Page 15Adding a New Transmitter into the System1. Turn on the ignition.2. Press and hold the Override switch.• The

installation_MS5500.qxd 12/6/99 11:59 AM Page 2

Page 16 - MS5500 Installation ManualSystem Initialization and Default ResetFollowing this procedure will set all System Programming Parameters to fac

MS5500 Installation Manual - Page 17Programmable System Parameters1. Ignition Controlled Door Locking. Selects whether or not the system automatica

Page 18 - MS5500 Installation Manual2 chirps = Logic Sensor II 3 chirps = Optional sensor4 chirps = hood/trunkWhen Audible Tamper Alert report

MS5500 Installation Manual - Page 19the 30 seconds, the output will turn off.When the Latched or Timed outputs are activated: • Armingthe system w

Page 20 - MS5500 Installation ManualBecause of its advanced design, the Logic Sensor II can be set for Shock and Motiondetection or Shock detection o

MS5500 Installation Manual - Page 21Remote Logic Sensor II BypassIn case of extreme weather conditions such as high winds, the Logic Sensor II can

Page 22 - MS5500 Installation ManualYou can use this chart to quickly identify and interpret the MS5500 system’s chirp indications andLED flashes.Ref

MS5500 Installation Manual - Page 23Door Lock DiagramsNegative TriggerPositive Trigger Voltage ReversalAftermarket Actuators Vacuum Lock SystemWhit

Page 24 - MS5500 Installation ManualDRIVER DOORACTUATORYellow/white wire(-) AUX. 1 outputCUTPASSENGER DOORACTUATORSFACTORY DOOR LOCK MODULEWhite/blue

MS5500 Installation Manual - Page 25The following are some suggested uses for the programmable Auxiliary Function 2 Output.Tech TipsRemote Control

1. Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12. Install

Page 26 - MS5500 Installation ManualNotesinstallation_MS5500.qxd 12/6/99 11:59 AM Page 26

MS5500 Installation Manual - Page 27installation_MS5500.qxd 12/6/99 11:59 AM Page 27

Ungo Security CorporationA Clarion Company661 West Redondo Beach Blvd.Gardena, CA 90247800-Go-Clarionwww.clarionmultimedia© Ungo Security Corporation,

installation_MS5500.qxd 12/6/99 11:59 AM Page 4

MS5500 Installation Manual - Page 11. Be sure to read the manual thoroughly before beginning the installation to ensure a properunderstanding of th

Page 2 - MS5500 Installation Manual1. Use a Volt / Ohm meter to test all wires. Do not use a test light.2. Good power and ground connections are ess

MS5500 Installation Manual - Page 3Main Unit The main unit should be mounted in the interior of the vehicle. Do not mount the main unitin the eng

Page 4 - MS5500 Installation ManualEXT2 Extended Range Antenna (optional)The optional EXT2 is a tuned, coaxial antenna, designed to be used with the

MS5500 Installation Manual - Page 5Mounting For Shock and Motion SensitivityMounting ForShock Sensitivity OnlyMotion SensitivityFront/RearSide to S