NOTE: This product is intended for installation by a professional installer only!Any attempt to install this product by any person other than a traine
11pro security programmer Interface, 3-Pin BLACK plugThe BLACK three-pin port is provided for programming of the unit. When using the ProSecurity Prog
12shock sensor harness, 4-pin WHITE plugGREEN (-) Multiplex InputInputs shorter than 0.8 seconds will trigger the warning response, while inputs longe
13light flash jumperThis jumper is used to determine the light flash output. In the (+) position, the on-board relay is enabled andthe unit will outpu
141. Open a door. (The H1/5 GREEN wire or the H1/7 VIOLET wire must be con-nected.)2. Ignition. Turn the ignition on, then back off: (The H1/9 YELLO
152. Then press the Override switch once more and hold it.For example, if you just programmed the third feature in the menu and you would like to prog
16menu #2 - advanced featuresfeature descriptionsThe features of the system are described below. Features that have additional settings that can be se
171-4 ACTIVE/PASSIVE LOCKING: If passive arming is selected in step 1-1, then the system can be pro-grammed to either lock the doors when passive armi
18menu #2 - advanced features2-1 SIREN/HORN HONK: The system can be programmed to output pulses instead of a continuous out-put when the system is tri
19ative pulses instead of a single pulse. At the same time, the GREEN H2/A wire will supply two positivepulses instead of a single pulse. This makes i
204. Press the remote button: While holding the Override switch, press the buttonfrom the remote that you wish to assign to the selected channel. The
3table of contentsprimary harness (H1) wire connection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4primary har
21remote configurationsThe remotes can be programmed with the standard or single button arm/disarm configurations byusing the Auto Learn functions in
22diagnosticsThe system’s microprocessor monitors and reports all active and violated zones when arming and dis-arming. LED flashes indicate the activ
23security diagnosticsThe system stores the last two full triggers in memory. These are not erasable. Each time the unit seesa full trigger, the older
24power-uppower-up ensures that the when the system is powered up it will return to the same state it was in whenpower is disconnected. For a full des
25Door input does not respond with the progressive trigger, but with immediate full alarm.➤ What zone does the LED indicate? If the LED indicates that
26wiring quick reference guide
Get StartedGet ProtectedUngo Pro Security661 W. Redondo Beach Blvd.Gardena, Ca. 90247800-GO-CLARION© 2003 Directed Electronics, Inc. - All rights rese
4primary harness (H1) wire connection guideprimary harness wiring diagram____________________________________primary harness wiring instructionsThis g
5H1/2 WHITE (+/-) light flash outputAs shipped, the H1/2 WHITE wire should be connected to the (+) parking light wire. If the light flashpolarity jump
6H1/3 WHITE/BLUE 200 mA (-) channel 3 outputThis wire provides a (-) 200 mA output whenever the remote button(s) controlling Channel 3 is pressed.This
7NNOOTTEE::If using a door trigger wire that has a delay, Advanced Menu 2, feature 6, or the Pro SecurityProgrammer can be used to turn the notificati
8H1/9 YELLOW (+) ignition inputConnect this wire to the (+) 12 volts ignition wire. This wire is pre-wired to the starter kill relay and mustshow (+)
9H1/12 RED/WHITE 200 mA (-) channel 2 outputWhen the system receives the code controlling channel 2 for longer than 1.5 seconds, the RED/WHITEwill sup
10peripheral plug-in harnessesLED, 2-pin WHITE plugThe LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make sure the LED wires ar
Commentaires sur ces manuels